Industriedruckregler
Requirements Specification: as requested Process data: Media: n.d. P1 (= set for overpressure): psig adjusting 4-6 / 270 to 410 mbar P2 (= Set n is vacuum): 70-150psig / 4.8 to 10.3 barg In the case of order: specify adjustment weight and setting for the opening pressure, as well as the material for the diaphragm seal Flow: n.d. Process Connection: DN80, flange according to EN 1092-1, form B1, PN16 Weight: 29 kg Size: (W) is about 405 x 490 x 250 mm
Ersetzt 46E-3A17-05030090D Nur in Verbindung mit 764P (Pos. 1) Anforderungsspezifikation: wie angefragt Prozessdaten: Medium: n.d. P1: n.d. Flow: n.d. Prozess-Anschluss: ANSI-Flansch 2“, 150 lbs, RF Gewicht: ca. 19 kg Größe: (BxHxT) ca. 255 x 190 x 165 mm PNEUMATIC CONTROL VALVE MODEL 2296, (you must order 764P to order this code – also note the higher bench range)- 46E-310S-0B500090E = PNEUMATIC CONTROL VALVE MODEL 2296, DN50 SIZE, SST BODY/BONNET,; 150# FLANGED OPT-30 CONNECTION; S1 TRIM, FULL PORT, = % CHARACTERISTIC; STANDARD CONSTRUCTION; MODEL C27 ACTUATOR, ATO-FC, 1.0-4.2 BARG BENCH SET; 764P DIRECT ACTING CONTROLLER W/AIRSET AND MOUNTING BRACKETS; NO POSITIONER; OPT-3 HANDWHEEL ASSEMBLY; STANDARD COMMERCIAL CLEANING & PAINTING;
Requirements Specification: as requested Process data: Media: n.d. P1: n.d. Flow: n.d. Process Connection: ANSI flange 2 ", 150 lbs, RF Weight: 19 kg Size: (WxHxD) approx 255 x 190 x 165 mm PNEUMATIC CONTROL VALVE MODEL 2296, DN50 SIZE, SST BODY / BONNET ,; 150 # FLANGED OPT-30 CONNECTION; MODEL C27 ACTUATOR, 0:34 to 1:03 BARG BENCH RANGE, REVERSE ACTION ATO-FC,% = CHARACTERISTIC, FULL PORT, S1 TRIM; NO POSITIONER; NO ENCLOSURE RATING; NO HAND WHEEL ASSEMBLY; STANDARD COMMERCIAL CLEANING & PAINTING;
non-oxygen, Aramid/SBR-B 1/4" (8) 2 B3 B4 20-80 (1.3-5.5) 2 B
Requirements Specification: as requested Process data: Media: n.d. P1: n.d. P2 (= signal output): 3-15psig / 0,2-1,03barg Flow: n.d. Process connection: NPT, 1/4 ", female thread Weight: 2.5 kg Size: (WxHxD) 125 x 125 x 105 mm MODEL "764P" PNEUMATIC CONTROLLER PRESSURE BARG 0:21 to 1:03 OUTPUT CONTROL BRONZE HOUSING (PNEU CIRCUIT) DN6 NPT PNEUMATIC CONNECTION ;; SST WETTED CONSTRUCTION; 316SST UPPER CASING & DIAPHRAGM, ductile iron LOWER CASING; 00:07 TO 2:07 BARG PRESSURE RANGE; DN8 NPT PROCESS CONNECTION @ CENTER OF UPPER CASING DIAPH ;; 5200P AIRSET, 0-2.07 BARG; STANDARD / COMMERCIAL CLEANING & PAINTING;
Druckmittler in Industriequalität
CASHCO - Industrial pressure regulator PNEUMATIC CONTROL VALVE MODEL 2296, SIZE DN25, GT BODY / BONNET ,; NPT SCREWED CONNECTION; MODEL C27 ACTUATOR, 0:34 to 1:03 BARG BENCH RANGE, REVERSE ACTION ATO-FC, LINEAR CHARACTERISTIC, FULL PORT, S1 TRIM; NO POSITIONER; NO ENCLOSURE RATING; NO HAND WHEEL ASSEMBLY; STANDARD COMMERCIAL CLEANING & PAINTING; Requirements Specification: as requested Process data: undefined Process connection: NPT fem. Weight: 12 kg Size: 230 x 230 x 340 mm
PRESSURE REDUCING VALVES, PRESSURE DESIGNATION:400 PSIG
oxygen trace analyzer,100-1000PPM,programmable two alarming point,4-20mA output,W/RS232,220V+/-10%, 50-60HZ
Anforderungsspezifikation: wie angefragt Prozessdaten: Medium: n.d. P1: n.d. P2 (=Set): 3-14psig/0,2-0,96 barg Flow: n.d. Prozess-Anschluss: ANSI-Flansch 1“, 150 lbs, RF Gewicht: ca. 10,5 kg Größe: (BxHxT) ca. 245 x 410 x 245 mm (must specify inlet supply pressure, set point, and dip tube length with order) P1WSSNA5VHSB000000 = DN25 SIZE MODEL 1078 PILOT OPERATED VACU-GARD VERTICAL OUTLET POSITION, INTEGRAL DIP-TUBE; PED COMPLIANCE REFER TO DIRECTIVE 97/23/EC.; 316 SST BODY, TRIM, SST DIAPHRAGM CASES WITH SST FITTINGS AND TUBING; SUPPLY PRESSURE GAUGE 0 - 6.9 BARG, TANK GAUGE 0 - 350 MBAR; DN25 150# RF FLANGES ATTACHED WITH NIPPLES; 50% FLOW PLUG; FLUOROCARBON ELASTOMER (FKM) SOFT SEATS & SEALS; 0.2 - .96 BARG RANGE SPRING; SST EXTERNAL PILOT FILTER;
RANGER ROTARY CONTROL VALVE
CASHCO – Industriedruckregler Modell „D-57“, Chlorine Service
Pressure test
DIFFERENTIAL PRESSURE REDUCING REGULAT
industrial control valve
Valve Diaphragm
Valve Diaphragm
CONTROLLER:PRESSURE
